Products

For high speed low carbon dry drawing.

Ability to forward and reverse jog blocks for easy threading.

Fully automatic speed control for all reduction ratios.

Power transmission by trapezoidal belts and worm gear reducers.

Block cooling by forced water circulation.

Electromagnetic brakes on all blocks.

Electronic safeties on all power supplies.

Rotating water cooled dies on all blocks.

Up to 13 block machines.

Block diameter 460 mm.

Inlet diameter 6.5 mm (0.25") at 38-50 kg/mm2 (54.00-70.00 psi).

Minimum floor space.

For drawing fine low carbon wire.

Speed control by auto-centered dancer arms.

All blocks are belt driven.

Hardened cast iron blocks.

Block cooling by forced water circulation.

Electromagnetic brakes on all blocks.

Electronic safeties on all power supplies.

Rotating water cooled dies on all block.

Up to 8 block machines.

Block diameter 350 mm.

Inlet diameter up to 2 mm.

Used to spool take up wire from high speed drawing machines.

The spools are loaded and unloaded by means of a hydraulically aperated lifting table. The sliding tail stock is also hydraulically controlled, and equipped with a braking machanism.

The speed is automatically adjusted to tthe wire line speed ad is the traverse laying mechanism.

Spool size 1150 mm (45") diameter.

Spool weight 2.5 tonnes (5500 lbs).

Wire diameters from 0.5 (0.2") to 6 mm (0.23").

Maximum spooler speed 30 m/sec (100 ft/sec.).

These fluidized bed P.V.C. coating lines consist of:

- Pay off and straightener

- Primer coating

- Pre heater

- Fluidized bed P.V.C. coating

- Curing oven

- Quenching

- Take ups

The hot air heating and curing furnaces are fabricated from stainless steel with stainless steel fans.

Automatic P.V.C. pellet handing system.

Fume extraction is available.

Wire diameters from 1.0 (0.04") tp 5 mm (0.20)

Speed up to 100 m/min (320 ft/min)

These fluidized bed P.V.C. coating lines consist of:

- Mesh or net straightener

- Primer coating

- Pre heater

- Fluidized bed P.V.C. coating

- Curing oven

- Quenching

- Puller

The hot air heating and curing furnaces are fabricated from stainless steel with high efficiency stainless steel fans.
Automatic P.V.C. pellet handling system.
Fume extraction is available.

Widths or product up to 2.5 m (8'-0")

Maximum wire diameter 3.5 mm (0.14")

Speeds up to 20 m/min (65 ft/min)

Fully automatic take ups for galvanized or P.V.C. coated welded mesh or netting.

Operator needed only when material is to be applied.

- Automatic shearing

- Roll strapping

- Automatic label insertion

- Widths up to 2.5 m (8'-0")

- Maximum wire diameter 3.5 mm (0.14")

- Production up to 48 rolls per hour with a single take up

- Double roll take up available

To produce flat panels from rolls of welded mesh or netting.

- 7 motorized straightening rolls

- Hydraulic double cut shears to remove the mesh ends

- Panel width up to 2 meters (6'-6")

- Panel lenght up to 6 meters (20'-0")

- Maximum wire diameter 3.5 mm (0.14")

- Maximum mesh size 100 mm (4")

- Maximum mesh 25 mm (1")

- Maximum production 6 panels per minute 1 meter long (3'-3")

These individual drive take ups can be used for galvanized, plastic coated or bright high or low carbon steel wire.

They can be supplied with individual or common drive motorized bases for pattern lay, or stationary bases for regular lay.

The duble blocks and pressure rolls are hard coated for long life.

Two plane straightener are included for cast and helix control.

All motors can be supplied A.C. or D.C. speed control.

Accumulation can be manual or automatic.

Individually driven live blocks are used for low or high carbon, bright or galvanized steel wire, to produce a torsion free package.

The double blocks and pressure rolls are hard coated for long life.

The acumulation arms are used to rotate the free tuming bases for regular lay, or syncronized driven base for pattern lay.

All motors can be supplied with either A.C. or D.C. controls.

Used as take ups for galvanizing lines, these spoolers have two motors, one for a constant line pull and the other to drive the spooler giving constant torsion control.

Spool size range from 900 mm (36") to 1150 mm (45") diameter.

Line speeds up tto 150 m/min (500 ft/min).

Spool weights up to 2.5 tonnes (5500 lbs).

Used to pay off spools for galvanizing and P.V.C. lines.

These pay offs are dancer arm controlled to allow constant wire pull and speed, they are equipped with an overrun brake.

Spool size rangge from 900 mm (36") to 1150 mm (45") diameter can be used.

Line speed up to 150 m/min (500 ft/min).

Spool weight up to 2.5 tonnes (5500 lbs).